Marketing, Sales & Project Management: Glenco Carpentry Sessions 9 & 10

The overhanging part of a rafter that extends beyond the exterior wall is defined as the

The recesses cut into the door to receive the hinges are called

When constructing a brick veneer wall, which of the following statements would meet proper construction and code requirements?

In standard kraft-faced insulation, the vapor barrier must

What type of rafters are shown by #2 in the figure?

Interior doors have a standard height of?

From the choices below, select what is used to attach brick veneer to wood framing.

You are installing a second layer of insulation on an attic floor. What is the best way to install this second layer of insulation?

What part of a roof truss is indicated by #1 in the figure?

Standard thickness for interior doors are

What part of the masonry structure requires angle iron?

Which type of drywall would be required above a bath tub?

A benchmark on a site plan has an elevation of 118.42 feet. Finish grade has an elevation of 115.22 feet. The finish grade is how many feet lower or higher than the benchmark?

An interior door is positioned in a

In calculating for the number of treads and height of risers what 2 items are required?

The most common edge used for drywall is

What part of a roof truss is indicated by #1 in the figure?

Door casing is set back off the face of the jamb approximately

Stool and apron trim would be found at which location

Best describes the form work for wet plaster

The most common type of truss used in homes today is the

Standard hinge spacing for a 2 hinged door is

Kitchen cabinets are installed by the use of

From the choices below, select the component that is not part of a drop ceiling grid system.

What word best describes sheet metal used to protect the house from water leakage?

The visible part of overlapped shingles is called ____________

Nylon or polyester bristle paint brushes are best suited for use with

To make the insertion of ceiling tiles easier, what is the recommended minimum spacing between the bottom of framing members and the top edge of the drop ceiling grid?

A window which consists of an upper and lower sash that can both slide vertically in the side jambs is known as a?

From the choices below, select the best term for the following definition. The visible part of an overlapped shingle is called?

From the choices below, select the material with the highest R value?

16 x 16 fiber board ceiling tiles require _____ staples 9/16 long along each flanged edge.

Fasteners for plywood soffit is to be spaced approximately how many inches apart?

What is the size of a standard shingle?

Insulation is rated for heat reflectivity using which symbol?

12 x 12 fiber board ceiling tiles require _____ staples 9/16 long along each flanged edge.

A home under construction is going to be built with a chimney extending above the roof. What is the most effective method to prevent ice from building up on the high side of the chimney?

How many fasteners are required for each individual asphalt strip shingle?

The “R” value of an insulation product refers to

12 x 12 fiber board ceiling tiles require _____ staples 9/16 long along each flanged edge.

What is the maximum span allowed for 1/2-inch plywood with a span rating stamp of 24/16 which is being used for roof sheathing?

When roofing, what is the proper method for nailing shingles?

Insulation in new construction must be installed

With painted wood siding, peeling results when ______________ in siding is drawn from the wood by the suns heat and pushes the paint from the surface

You are responsible for selecting the proper grade of plywood for a project. A sheathing grade of plywood has an ID index of 48/24. Plywood edges will be blocked. On what framing member would this plywood be permissible to use when spanning a maximum of 48″?

Outlet ventilation is typically installed in the

The most effective method for applying cellulose insulation in an attic is by using a

The main purpose of flagged tips in bristles is to

The span rating on a 15/32 sheet of O.S.B. is labeled 32/16. This material is sufficient for decking the 1st floor joists if the joists are ________ or less on center.

According to the Michigan Residential Code, each wood shingle or wood shake should be attached by

Best describes the temperature at which the air is completely saturated with moisture.

If 3/4 inch strip flooring is used, the 1st piece is located in what location to the wall?

The span rating on a 15/32 sheet of O.S.B. is labeled 32/16. This material is sufficient for the decking of the roof trusses if the trusses are ________ or less on center.

A new home is being constructed using board and batten siding. What best describes the battens?

Wide sheets of standard ___________ may be used as a vapor barrier within a crawl space.

The most common thickness of underlayment for vinyl flooring is _______.

What tool is used to measure vertical angles, run straight lines, and determine if a wall is plumb?

Represents the total heat transmission loss through structural materials

The installation of bevel wood siding requires a specific number of face-nailed nails per stud. Select the correct answer from the choices below for nailing 6 inch wide bevel wood siding.

In order to be effective, foil faced insulation must have the foil side ____________.

The actual dimension of 2 X 6 framing lumber is

What does fireblocking do?

Select the specific type of door from the choices below. What type of door consists of stiles, rails, and panels?

When installing aluminum or vinyl siding, what should be used to hold and secure the siding under the eaves?

You are responsible for insulating part a job. How should a vapor barrier on blanket (batts) insulation be installed?